The complete system comprises of followings:-
The system is a totally welded structure, which gives a tremendous amount of stability to the system. It has an equal area hydraulic cylinder attached to the base and an oil filled spherical seating is screwed to the top with Solid platen having hardness greater than 45-50HRC. The horizontal and vertical clearances are enough to test standard rock specimen under triaxial test. It can accommodate a triaxial cell with a sample size up to 90 mm size. Front cover is provided, made of acrylic sheet, as a protection to the operator while at the same time giving an unobstructive view of the specimen under test.
Loading Capacity of the unit
(Static & Dynamic) : 1000/2000kN
Total travel of the ram : 50mm
Clearance – Horizontal : 450mm
Vertical : 820mm
Platen Size : 250mm
The unit consists of metallic high pressure chamber. A hardened, ground and lapped frictionless plunger passes through the removable head. The cylinder is clamped to a base plate having four drilled take off positions for measurement of lateral pressure, pore pressure, back pressure and top drainage. The specimen pedestal and loading pads are also hardened. Spherical seating is provided at the top of the specimen loading pad for self alignment. Triaxial cell is suitable for specimen size ranging from Ex to Nx. Four sets of pedestals (Ex, Ax, Bx & Nx) are provided as standard along with the unit. Side jacks are also provided for lifting the cover of Triaxial cell.
Triaxial Cell has arrangement for taking out electrical leads of strain gauges pasted on the specimen.
MODEL : PRESSURE RANGE
HR72.535 : 0 – 7MPa
HR72.535 : 0 – 15MPa
HR72.540 : 0 – 35MPa
HR72.545 : 0 – 50MPa
HR72.550 : 0 – 70MPa
HR72.555 : 0 – 100MPa
Hydraulic power supplies are compact in design and are suitable for the supply of required flow and pressure for the move ment of the actuator. It has an oil tank of adequate capacity, vane type pump powered by a three phase motor. All the electrical controls including the temperature controller are fixed on one side of the tank. It includes all the accessories like pressure line filter, return line filter, oil level, relief valve, pressure gauge and shell & tube type heat exchanger. Anti vibration mountings are provided as standard along with the HPS. Cooling system for keeping oil within working temperature range is provided as standard. The system is kept at a distance from the loading unit and connected through flexible pipes.
TECHNICAL DETAILS
Flow of the pump : 40LPM
Motor capacity : 25HP
Capacity f the tank : 200litres
Operating pressure : 200Bars
NOTE – System will be supplied with necessary cable and fittings for the operation of the machine and machine operates on 440VAC 3 phase supply.
The Controllers are designed to maintain confining pressure at the set value with the help of servo valve based on PID closed loop feedback principle. Sensing back is from a sensitive pressure transducer. Pressure is maintained with in the range of +2 % irrespective of any deformation that takes place during testing of the specimen. A series of relays are provided for automatic actuation of the main pumping unit depending upon the volume change in the specimen. This unit can be operated by the same hydraulic power pack.
MODEL : PRESSURE RANGE
HR72.565 : 0.1 – 7MPa
HR72.570 : 0.2 – 15MPa
HR72.575 : 0.5 – 35MPa
HR72.585 : 0.5 – 50MPa
HR72.590 : 0.5 – 70MPa
HR72.595 : 0.5 – 100MPa
Control system provides the digital servo control, Wave generation for the axial loading, data acquisition, hydraulic control etc. for the continuous operation of the system.
(a) Signal Conditioning & Controlling Unit HEICO Servo controller basically consists of signal conditioning unit and controlling unit. Signal conditioning unit consists of conditioning modules for various transducers (e.g. Load Cell, Displacement Transducers etc.) that receives the output signal from these sensors and amplifies and process that signal as per the requirement and transfer it to computer through dedicated cables where it is accepted by the data acquisition system. The out put from the signal conditioning unit for each transducers range from 0-5V.The controlling unit controls the movement of the RAM with respect to the signal input on feed back basis either from LOAD CELL or DISPLACEMENT sensor.
It consists of dedicated servo-controller card that gives the desired processed signal through the P.I.D controller to the servo valve to operate either of the control modes i.e. Load mode or Displacement mode. It also sends the signal to computer and accepts the command from the software to operate in desired manner. The system can generate sine, triangular or square wave form and also can accept external input wave form as generated in the field. The programming facility is given to operate the system in STATIC MODE at programmed rate of loading in both Load and Displacement controls. In DYNAMIC MODE the cycling can be done at a frequency from 0.01Hz-10Hz or even higher.
Specifications of Controller
(b) Computer for Controlling and Data acquisition System is provided with dedicated computer of latest available configuration with built in data
acquisition card and wave generator.
Data acquisition card
The PCI Bus advanced data acquisition card provides the following advanced features
Up to 100 KHz A/D Sampling Rates
CONTROL SOFTWARE
Controlling and On-line Data Acquisition to PC through user friendly software and Statistical Analysis of the results obtained.
Salient Features
Analysis Software
b) Displacement v/s Time
c) Load v/s Displacement
d) Stress v/s Strain
This unit is essentially used for finding out poisous ratio of rocks specimen. It has displacement sensors both for lateral extension and for compression.
Total displacement is ± 2mm with sensitivity of 0.001 mm. Complete with digital display.
Copyright @2022 heicoin.com All rights reserved.