Aggregate Testing
Mechanical Rotating Sample Divider (Motorised)
IS : 1607-1960
HA 50.05
For obtaining representative sample for sieve analysis. It is suitable for dry sands, fine powders, ores, refractory materials, mineral aggregates, pigments, powered coal, soap, cement etc. Up to a maximum particle size of 3 mm.
The sampler consists of the following :-
- A hopper with an adjustable orificehaving six holes of 1.6 mm, 3 mm, 5 mm, 6 mm, 8 mm and 10 mm dia and a shutter.
- A rotating spreader turning at approximately 440 rpm to distribute the sample over the trough. Suitable for operation on 220v, 50 Hz, single phase supply
Cylindrical Measures
IS : 2386 (Part - III) -1963, IS : 10079-1982
HA 50.30
Required for determining the bulk density or unit weight of aggregates.
Three calibrated cylindrical measures one each of 3 litre, 15 litre and 30 litre capacity made out of steel sheet with handles, complete with one tamping rod 16 mm dia x 60 cm long rounded at one end.
Buoyancy Balance
HA 50.43
Buoyancy balance is a multi purpose type of unit with electronic balance for the determination of density of the sample, weight in water, volume of the sample, or for analysis of fresh concrete.
The unit consists of a tubular frame, a carriage connected through chain to a ratchet. Balance is kept on the top of the table and has a hook for hanging the specimen. Powel and ratchet is provided to raise the plate form along with the plastic container filled with water. Balance has the capacity of 16kg.
Sand Absorption Cone and Tamper
ASTM C 128-84, AASHO T 84
HA 50.50
For determining the slump of fine aggregate in estimation of absorption of fine aggregate.
It consists of the following :-
- A metal mould in the form of frustumof a cone 40 mm dia at the top, 90 mm dia at the bottom and 73 mm in height.
- A metal tamper having a flat circular tamping face 25 mm dia and weighing 340 g approximately.
Deval Attrition Testing Machine
IS : 2386 (part IV) - 1963
HA 50.55
For determining the abrasion value of coarse aggregate.
It consists of the following :-
- Two hollow cast iron cylinders closed at one end and fitted with tightly fitting covers at the other and mounted on a shaft at an angle of 30o to the axis of the shaft. The cylinders are of 20 cm internal diameter and 34 cm deep.
- A shaft adjusted to rotate at 30-33 rpm by reduction gear mechanism operated by a motor.
- A revolution counter. Suitable for operation on 440 V, 50 Hz, 3 phase supply.
Los Angels Abrasion Testing Machine
IS : 10070-1982
HA 50.555
Used for estimation of abrasion value of coarse aggregate.
The machine comprises the following :-
- A hollow steel cylinder mounted on a sturdy frame on ball bearings capable of rotating about its axis in a horizontal position.
- A detachable shelf fitted inside the cylinder at a distance of 1250 mm from the opening measured along the circumstance in the direction of rotation.
- A motor with reduction gear which runs the drum at 30-33 rpm.
- A tray.
- A revolution counter.
- Abrasive charge consisting of 12 steel ball approximately 48 mm dia and each weighing between 390 and 445 g. Suitable for operation on 440 v, 50 Hz, 3 phase supply.
Dorry Abrasion Testing Machine
BS : 812-1967
HA 50.70
For determination of the resistance of aggregates to surface wear by abrasion. The apparatus comprises the following :-
- A circular disc mounted on a reduction gear driven by an electric motor at about 28-30 rpm.
- Two large trays for holding the sample.
- Two small trays for sample.
- Two conical hoppers for sand.
- Two sample try holders.
- Two sets of weights for loading the samples.
- A revolution counter.
Suitable for operation on 220 V, 50 Hz, single phase supply.
Aggregate Impact Test Apparatus with Counter
IS : 9377-1979
HA 50.80
Required for determining the Impact Value of coarse aggregate.
It consists of the following :-
- Fitted with an automatic blow counter.
- A heavy circular base with two vertical guides fitted with a cross bar at the top.
- A hammer of 13.75 kg mass which can be raised and allowed to fall freely through 380 +5 mm with locking arrangement.
- A cylindrical cup, a metal measure and a tamping rod 10 mm dia x 230 mm long.
Reaction Container
IS:2386 (Part VII)
HA 50.95
The reaction container is one of the important apparatus, required for determination of the Potential Alkali Reactivity of aggregates by chemical method when used in concrete having high alkali cement. It is made from stainless steel and fitted with air tight cover, held in position with special clamp.
Tile Abrasion Testing Machine
IS : 1237-1980, IS : 1706 - 1972
HA 50.100
Used for determining the resistance of flooring tiles to wear or abrasion.
It consists of the following :-
- A grinding disc furnished with a replaceable grinding path and rotating horizontally about its vertical axis.
- A circular tray enclosing the grinding disc.
- Holding device for test specimen.
- Reduction gear coupled to a motor for operation on 220 v, 50 Hz, single phase supply electronic.
- Revolution counter. (Preset cumulative).
- A 7.5 kg weight to apply 30 kg load on specimen through lever.
Accelerated Aggregate Polishing Machine
IS : 2386 (Part V)-1963
HA 50.105
Used for polishing the road aggregate specimens for determining the polished stone value.
It consists of :-
- A road wheel suitable for clamping 14 road stone specimens on its periphery.
- A rubber tyred wheel fitted with a lever system to exert a load of 40 kgf. on the road wheel.
- An electrically operated vibrating hopper unit for feeding emery powder over the road wheel.
- A water reservoir for feeding water into hopper.
- Seven moulds for the preparation of samples.
Suitable for operation on 220v, 50 Hz, single phase supply.
Skid Resistance Tester
HA 50.107
This apparatus consists of a spring-loaded rubber shoe mounted on a pendulum arm. The pendulum arm can be adjusted vertically from a rigid suport column when in operation. The base has three adjustable feet so that the swing of the pendulum during test moves through a truly circular path while in operation directly on a road surface. An essential feature of this apparatus is the fact that the slider is made from a carefully graded rubber specially selected and certified by Transport and Road Research Laboratory of Great Britain . All bearing and working parts are enclosed.